![]() Finally, tie the 2 lengths of string to a third piece of string at the junction where the 2 strings meet to make your brindle and line. Repeat this process with the other dowel and a second piece of string. Run the other end of the string to the opposite end of the dowel and tie it there. Next, tie a piece of string to the end of one of the dowels. Fold the excess plastic over the dowel and press it into the hot glue. Then, lay the frame on top of the sheet you’ve cut, and line the inside of each dowel with hot glue. ![]() ![]() Set the frame aside, and cut around the outline you drew, adding 2 inches (5 cm) to each side as you cut. Now, lay your frame on top of a garbage bag or sheet of thin plastic, and outline the frame with a marker. Pull the string tight so it's taut, then tie the 2 ends into a knot. Use the notches you cut to keep the string in place. Run a long length of string around the ends of the dowels to connect the 4 ends. Here is an easy-to-read list of our top 10 safety tips for flying a kite. For example: Don’t fly too close to a tree or don’t fly a kite when it’s raining. You may have heard all sorts of advice when getting ready to go out and fly a kite. ![]() Next, cut a notch in the end of each dowel using a small knife. Written by Lee & Cameron in Kite Flying Basics. Wait a few minutes for the hot glue to dry. Wrap string around the point where the 2 dowels meet, and use hot glue to cover the string and seal the 2 dowels together. Then, lay the longer dowel down on a flat surface, and place the shorter dowel on top of it about 4 inches (12.5 cm) above the midpoint so they're perpindicular. Cut one of the dowels so it's about 6 inches (15 cm) shorter than the other one. * Use only cotton threads or any natural fibre that is free from metallic or glass components.To make a kite, first you'll need 2 wooden dowels that are less than 2 inches (5 cm) in diameter and about 40 inches (100 cm) long. * Do not use a metal coated string ( manjha) as it can lead to tripping or even electrocution. * Do not fly kites close to roads or near moving traffic. * Do not fetch or touch the kite or string entangled in electrical lines/network. * Do not fly kites near electrical installations and overhead power lines. It noted in its advisory the following important points: #KiteFlying #StaySafe #SafeKiteFlying #TataPowerDDL #KiteFlyingSafetyTips /B7C5FHN0Io If the manjha is a metal-coated one, it can prove to be dangerous to not only to the person flying the kite, but also others, and it may also disrupt electricity supply of an area.Īlways use kite thread that is free from metallic or glass components as it can cause serious injuries to humans and birds. In a press release, it noted that the string of the kite, called the ‘ manjha’ often comes in contact and gets entangled with an overhead live wire. #KiteFlying #StaySafe #SafeKiteFlying #TataPowerDDL #KiteFlyingSafetyTips /iAiMInkmMP If any kite or kite string (manjha) gets entangled in overhead power lines, stay away from it, as electricity can travel down the cord, potentially causing serious injuries. Oftentimes this will be at the beach or in an open field far from trees as these can hinder your ability to launch the kite properly. (Express photo by Vishal Srivastava)īut, in the recent past, there have been many accidents caused due to kite flying, and also harm to animals and birds - all of which are avoidable, and one simply needs to exercise caution while participating in the activity.Įarlier this month, the Tata Power-DDL - a leading utility supplying electricity in North Delhi - had appealed to Delhiites to not fly kites near electrical installations and overhead power lines ahead of the festival season. Step 1: When choosing a location to fly your kite, pick an area with lots of wind. Children fly tricolour kites in Lucknow ahead of the 75th Independence Day. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |